Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello all,
I saw their was a new update for the nRF518-SDK and I was wondering how I should update this in Keil. Is this just a simple replace folder? Replacing:
...
I inherited an ANT/BLE nRF51422 project a couple of weeks ago.
It used SDK v6.1.0 and S310 SoftDevice v1.0.0
At the time, I'm sure that the SoftDevice download said...
I'm attempting to troubleshoot problems between dev teams. One team is having some issues & I notice that their binary is slightly larger when built from exactly the same...
I am trying to use the laird BL620 module not for the smartBasic, but to run my own firmware.
I have just set it up, connected to my old segger JLink debugger.
In Keil I...
Press the Connect button on the Smart ponaep NRF Uart V2.0 recognizes the page reongil signal
Disconnect state, allow to boil for your smartphone to wait about 20 minutes...
I am pretty new to the nRF51822 in the firmware side. I have been doing hardware design for many years but need a little help getting started with firmware.
Does anyone...
When the bootloader in SDK 8.0.0 checks whether the application is valid, it only computes the CRC for the application if the CRC in the bootloader settings for that bank...
Hi,
I try to make characteristic broadcasting through advertisement data packets.
Added these codes below, but no yet work. Is there any example for this work ?
char_md...
SDK v8 release notes specifically state that there is no S310 support. Are there plans to support the S310 soft device in future SDK releases or are you discontinuing the...
Hi,
I do some test for nrf51822 power consumption.result as below:
my board
1.system off mode:270uA
2.system on sleep mode(no UART,no GPIOTE):300uA
3.system on sleep...
hi -- i'm a big fan of the NRF24L01+ chip, i've written a high-performance driver for it using most of the features, relying heavily on Dynamic Payload and Auto-acknowledgement...
Hi
I'm trying to program a nRF51 DK (pca10028) with the heart rate demo "ble_app_hrs_s110_pca10028", but for some reason it doesn't respond... at all.
I started off...
Hi Team,
I would like to implement a second bootloader to program an external serial Flash chip.
Currently using S110 V7.1.
My current thinking is to create another...
Hello--
I have an NRF51422-DK devkit (PCA10028, v1.1.0) and noticed that pin P0.31 is not brought out to the connectors or mentioned anywhere in the nRF51-DK-HW schematic...
