Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
Along with S110 BLE stack I programmed my application, which I managed to do without any conflict.
My application is not working properly and neither control is transfered...
how much time of keep level HIGH/LOW can make nRF51822 detected the HIGH/LOW level and generate an interrupt?
how width of impulse need to generate an interrupt?
Hi Team,
I was trying to load firmware to external board using nRF51-DK.
I have successfully programmed the boards many times and now when I am trying, LED (LD5) on nRF...
Hi all,
I downloaded the nrf51SDK_.8.0.0 from nordic site and tried to flash the new softdevice s110 but failed. I used an android application to flash it over the air...
Hi:
i use ble_app_uart project and want to change the UUID lenth(128 bit) to be 32 bit;but i change "nus_base_uuid" to be 4 byte and change "uuid128[16]" to be "uuid128[4...
Hi,
Does hardware that has already a Qualified design Listing (Bluetooth.org) requires re-testing of the RF-PHY ?
(refering to transmitter tests (i.e TRM-LE/CA/01/C (output...
Hi,
Im using a module NRF24L01 + LNA bought off ebay, connected it to msp430 via SPI interface. All spi communications are going solid, I manage to completely configure module...
I am trying to create a file and write to it during runtime. When I use fopen with "w" option to create a new file, the file pointer is always retuned to be NULL.
Is there...
Hi,
I recently tried SDK7.2 on PCA10028 board in order to make sure that SDK7.2 works well before I migrate my project to SDK7.2 codebase. My project code didn't work as...
Is it possible to do OTA from one nRF51822 to another? Is so how, and is not why?
I am using S120 and S130 for my applications and would like one device to uppgrade another...
Nordic has provided a good SPP implementation over BLE.
devzone.nordicsemi.com/.../
However, will it raise power consumption and cause BLE to lose its low-power characteristics...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
