I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi,
I'm wondering why I can't see any packet from example led_mesh in your's sniffer?
Theoretically it's only Nonconnectable Advertisements or I miss some information...
What will be the price of nrf52 chips compared to nrf51?
Will there be any cheaper version of nrf52 chips with limited capacbilities (e.g. less flash, ram)?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
Hi All,
My goal is to change the advertisement(when not "connected" to ble device) in every SPI Interrupt, depending on the data received i set corresponding data in advertisement...
In porting over my project from Keil to GCC using SDK 8.1.0 I can build and run just fine when I build with Keil but when I build with GCC and try to run sd_softdevice_enable...
Hi,
I trying to write an application with android for my nRF51822 device
I use Battery service example but every time i update battery level i need to request for changed...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi,all.i want to run DTM on pca10028 develop board and connect it to my pc via USB (JLink CDC UART Port) on the board.My pc operation system is ubuntu10.4. what is the port...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,all. i run example.py(nAN34 document) on ubuntu10.4,then get an error:
./example.py:line 13:unexcept error near "(";
./example.py:line 13:'def main():'
what's wrong...
Hey there,
I am having issues downloading the SDK for the NRF52. It just goes to a blank part of the page. Is there a better way for me to get a hold of this SDK?
T...
So after reading some material it seems like I can pretty much define which pins are responsible for I2C communication. Is there any limitation to which pins I can set? Does...
Hello,
There are many anomalies in the NRF52 Revision Engineering A (QFAA-AA0, QFAA-AC0) .
This revision it is the current chip?
If so, do you know when there will...
