Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
I am a beginner and I am trying to generate a data ready event and after that reading the FIFO_Count but FIFO_Count gives me the value 1024 that is the maximum possible size...
Hello,
We are in interaction design in a school in France and we must create a connected object. We bought a BLUETOOTH SMART BEACON KIT (nRF51822) and we would know what...
I used nrf51822_narrow module DT26.
softdevice : s110
application: ble_app_hids_mouse
sdk: nrf51_sdk_v6_1_0
Now , we are able to move the cursor with the mouse of the...
Hi,
In the nRF51-ble-bcast-mesh example, it is mentioned that "handle_count" refers to "The maximum number of handle-value pairs available to the application. May not be...
With reference to the IoT SDK for nrf51, I see the APIs and examples of either server or client.
In order to create mesh or peer-to-peer, which API should I use? Or do...
In the description of nRF51-ble-bcast-mesh, there is mentioned that there could be up to 155 mesh values:
There may be up to 155 "Mesh value" characteristics in the mesh...
Hi,
I'm wondering why I can't see any packet from example led_mesh in your's sniffer?
Theoretically it's only Nonconnectable Advertisements or I miss some information...
What will be the price of nrf52 chips compared to nrf51?
Will there be any cheaper version of nrf52 chips with limited capacbilities (e.g. less flash, ram)?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
Hi All,
My goal is to change the advertisement(when not "connected" to ble device) in every SPI Interrupt, depending on the data received i set corresponding data in advertisement...
In porting over my project from Keil to GCC using SDK 8.1.0 I can build and run just fine when I build with Keil but when I build with GCC and try to run sd_softdevice_enable...