Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi, i've just started to use the nRF8001, so forgive me if this is an obvious problem.
i'm using the nRF8001 with a microchip PIC processor.
i'm using the ace_tl_demo...
Hi,
I have read ANT Message protocol and Usage and tried to implement shared channel according to section 8.2. I am using nrf51422 and S210 and SDK 10.0.0
My master...
I'm trying to use TDD for my development of a BLE peripheral application, but I'm running into some problems. I'm using Ceedling, CMock, and Unity for my TDD environment,...
I'm trying to scan beacons. This is what I added to the example ble_app_uart_c :
case BLE_GAP_EVT_ADV_REPORT:
{
const ble_gap_evt_adv_report_t * p_adv_report = &p_gap_evt...
Hi all,
I have a problem in architecture of my application based on SD132v3 SDK12. It should interact with an iOS device as a peripheral and receive some data to display...
Hi,
I am using NRF51822 and SDK11 with S130. I have enabled WDT with 2000 as reload value as I'm using 1 second timer. But I want to immediately reset when a certain condition...
Sir,
We are using your radio component in our system since many years. We are in the process to get conformity with Japanese rules.
The lab in charge of testing is asking...
Hello,
I'm trying the ota tester with pca10040 board however the ota tester won't run.
System hangs around softdevice_enable() and goes to app_error_fault_handler. ...
In Android 5.x (API 21) and up, we are experiencing a problem with our BluetoothLeScanner, on some Samsung models like S4 Mini and S5 Mini.
More precisely, an error is being...
Hi,
I would like to use assembly language instructions for the following piece of code:
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<NUMBER_OF_SHORT_PULSES_TO_TURN_BSTR_ON;i...
Hi,
I wrote a function setting some GPIO pins, initiating an SPIM transfer (with EasyDMA), then waiting for the SPIM handler to signal end of transfer, and then set some...
HI,
I am using nrf51822 to communicate with ADT7320,using nRF51822 as the master,and the ADT7320 as the slave.I used the SPI master example,then i want to get temperature...
I've not been able to program the nRF51822 using the Blackmagic probe programmer because the nRF51822QFAAH1 seems to use a previously unseen device code of 0x008F
Could...
Hi guys!
Got a problem with re-initialising my SAADC to read my current battery voltage. I'm using SDK11 and don't want to migrate to v12, so I wanted to do a workaround...
