After programming the DK, it "fails to verify device" with the following log:
2025-07-08T09:42:05.940Z INFO Initialising the bundled nrfutil device 2025-07-08T09:42:05.957Z...
Hi,
I'm trying to send HTTPS commands (GET/POST) using the nRF9151-DK.
I’ve already completed the process using nRF Connect for Desktop . The device was recognized correctly...
Hi. I have an idea for a product and I'm looking into different platforms to start prototyping. Something nrf9160 based looks like the way to go, and it would be a huge advantage...
Hi,
I'm using nrf Connect mobile (for Android) app to exchange data (read/write) with a BLE device (server) over GATT.
I have a large characteristic (123 bytes) to exchange...
After full update modem firmware and reboot, i got this error:
E: Modem library init error: -116, lte_lc not initialized
The only way to work around is power cycle.Po...
Hi,
am working on nrf52840 withst7789v custom display . I have integrated the my display code using lvgl library with PMIC code in zephyr . while doing that I have configure...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
If I write a zero to the output register, and enable the pullup on the same pin, can I switch between driven low output and input with pullup simply by settting/clearing the...
Hello,
For our DFU solution we would like to read the current hardware/software revision of the module. But now we can only test the hardware/software revision of the application...
Dear All,
I can read two different ANT sensors sucessfully with my target system, but initialization of sensors only works first time. When changing sensorIDs of simulator...
HI, All.
I have some troubles:
Why MBR is erased when I erase or write the SorfDevice with 1kB at address 0x3000? My SorfDevice version is 7.1.0.
Thanks all.
Update...
Hello all,
When I try to implement the new watchdog driver it keeps saying that the NRF_DRV_WDT_DEAFULT_CONFIG is undeclared. What am I missing I have all the requered...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
hello,
In order to develop a project on master-bridge-slave,i found scan_start() in the ble_central program.But the function definition for sd_ble_gap_scan_start() in scan_start...
I am using nRF51422 SDK v8.0 and the board for evaluation is PCA10003. As I am using the BLE in GENERIC_KEYRING. The same I am trying to configure to send Immediate alert...
Hi,
I'm wondering if there's any way to check if a peripheral device was actively scanned? I can easily set my own scan response data but is there any message generated...
Hi all,
As i understand from useful discussion here, we can send one 20 bytes packet per connection when we use S120 to S110 direction, and this number could be increased...
Hello,
Working on my own code to integrate an arm chip with the nRF8001, after I read the device status, which says it's in Setup-mode, I'm sending the setup configuration...
Hi,
I want to know how sd_ble_gap_rssi_get API works? Is it send any BLE packets over radio to get RSSI whenever application calls this function. What are the sets of events...
