Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi!
I am using the nRF51822 to do some measurements regarding the capture effect ( en.wikipedia.org/.../Capture_effect).
My question now is: when does the radio latches...
Hi
I´ve got two boards with PIC 18F4620s connected to nRF24L01+ .
One is configured as Tx and the other as Rx.
I can read/write registers trough SPI in both boards, but...
Hi!
Im trying to read the rssi value in real-time from my connected beacon device. Im using a xcode sdk (nRF beacons). All I can find are UUID, Minor and Major values.
...
Hello all.
We have a simple ANT-page application that has the ability to send data as burst packets when requested. The code has been working well. We identified the need...
I'm trying to use nRF51 IoT SDK and setting raspberry pi as router.
When I enter the below command for connecting to nrf51, wlan connection is disconnected.
echo "connect...
My configuration:
NRF51822 v2
TWI
GPIOTE
Issue:
The gpio interrupt does not get triggered. I know that my twi device is changing the state of the gpio3...
Hello, I apologise for this being quite simple as questions go but I was wondering if anyone knew where to begin or if there is any good information out there on how to use...
Hi,
I need use the nrf51822 to connect to PC via usb ble adapter (virtual com port).
The PC side has the USB BLE dongle (adapter).
http://www.amazon.co.uk/Plugable-Bluetooth...
Hi....
Is there any issue in sending a value on a character in button_event_handler? When i tried it disconnection is happening.Am not using button service , just using...
When running the makefiles found in the esb/gcc_rx and esb/gcc_tx folders I get the following errors:
base:gcc_tx jnoble$ make
mkdir _build
"/Users/jnoble/hardware/nrf51822...
I have trouble compiling successfully even the simplest of example codes for the nRF51822 with the Keil MDK-ARM toolchain (v5).
For example, for the "blinky" project, I...
I have ported the example ble_app_beacon from sdk 7.2.0 for use with nrf51422_xxaa and softdevice s310 (v.2.00).
In the function ble_stack_init() there is a call to the...
Hello everyone,
I have two doubts related to pca10001 board:
What is the maximum amount of current
that can be pulled from a single GPIO
pin?
Does the...
Hello,
I just received new rev.3 nrf51822 chips, so I am migrating with my project to newest SDK version.
I installed Keil5 with that smart run-time environment manager...
