I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello community,
We have a requirement to do concurrent BLE peripheral and broadcaster roles with S132 stack. This seems to be one approach but a bit crude for our requirement...
Hello,
while reading the nrf52840_OPS_v0.5, I discovered, that there is a 32MHz peripheral clock. I did not found any reference to it in the rest of the document. Is there...
Hello,
we need to first enable GPIOTE+IRQ. Then after 1st IRQ we want to keep only GPIOTE and disable IRQ. We do not want to disable GPIOTE (because it works with PPI), but...
I'm currently doing tutorials with the nRF52832 DK and am asking myself this question. How would I connect the nRF52 SoCs to my PC for flashing? Also, how should I edit the...
Hello,
I do migration from SDK11 to SDK12 (S132-SD-v2.0.1 to S132-SD-v3.1.0) and my device (nRF52-DK) randomly got a MAC of 00:00:00:00:00:00.
Helped by the migration...
Hi,
I am using BLE UART application with softdevice S132 on nrf52832 board.
I wrote a code where where i am using systick interrupt, GPIOTE interrupt. Also code has SPI0...
I have been reading device manager of SDK10.0 for nrf51822 . I looked at dm_ble_evt_handler and whole device manager source code but i didn't found where keys like IRK , LTK...
Hi,
i am working with nRF24LE1's as one master and many slaves. I also use the RTC2 functionality for the register retention mode.
As i read in the documentation the...
Hello,
I would like to know if it would be possible to create a public repository on my github account where putting all dependencies for my project including the folder...
Hi Nordic,
I want to include this library ( github.com/.../MPU6050.cpp) in my project, which is an evolution from ant_ broadcast example, in C. However, and after reading...
My application:
I have a peripheral (S110) that registers important alerts and immediately broadcasts them to any central that is listening. There will be some amount ...
Everyone.
Do you use nrf_drv_adc when using nRF 52832's ADC?
Or are you controlling the ADC directly?
I am not good at nrf_drv_adc.
Is this justice?
Please tell us your...
Hi, I was setting my new computer and installed nRF5x-Command-Line-Tools-Win32 V9.2.1.
Then open nRFgo studio it requests an update with strong recommended. After the update...
When my program was running,An error occurred.The program ran here
（app_error_handler_bare）and the error_info is
0x00000004, how can I find out the reason of error_info...
