Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I am running the nRF51822 from a coin-cell. I need to measure the cell voltage. Until now, I have attached VDD to an ADC pin with a voltage divider and a capacitor...
Hello~
In my production line use jig contact my PCBA, and use Jlink connect to Nordic 51822 download FW, but I found sometime can use 500kHz and sometime can't use, just...
Hi
I am using nRF52(PCA10040) as a sniffer dongle, but it seems the sniffer mode cannot work, and shows the error log: "INFO: Error on port xx. file: Packet.py, line 245...
First step of trying to integrate S132 to a small OS is failing completely.
When I use SVC the system ends up in hanging in hard fault.
The SoD handler ends up trying...
I am testing to develop an application that sleep (system-on mode) for most of the time, and it wake-up periodically to send out somethings.
As I would like to lower the...
Hello,
After when I download the protocol stack（S132）.The target is NRF52832 chip，tool is J-link OB.
I choose to recover nrf52 ，then prompt unable to fine or open the...
Hi,
In ADC, we would be using the internal voltage generator as the reference voltage. How stable is the voltage coming out of the reference generator. Would it be always...
It appears that, if I wanted to write characteristics to my BLE device, I can utilize the writeCharacteristic method of the BluetoothGatt class. Is this the right way to go...
Hello,
I am currently for a quick solution to test NRF24LE1 compliance to FCC. Can you provide me with any code if possible? As i could see from the website only an application...
Hi,
We can utilize the 31 bytes of advertising packet as well as 31 bytes of scan response packet which in total makes it 62 bytes of advertising data. What is the effect...
Hi dear Nordic Engineers.
We going to move from FN-LINK (Realtek) I.C. BLE to nRF52.
FN-LINK uses HCI (UART) BLE the Interface to communicate with our embd. LINUX.
How...
Hi all,
I'm using pca10040 board with sdk version nRF5_SDK_11.0.0-2.alpha_bc3f6a0.
There i'm using example code of spi handling. Instead of nrf_log_printf i changed...
Hello,
There's any known issue realated with DFU and Android 7.0? When we try to update firmware with nRF Connect or our APP we get an error (hex file error), but when...
I am going to develop an application on nfr51422 that requires very low current consumption. Basically we plan to make the nfr51 to "sleep", and it will wake up constantly...
