Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello, sorry if this is a stupid question.I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.I want to modify ble_app_hids_keyboard
to be able to send Volumn_up/down keys to android...
Hello:
I am use nrf51822 to transfor data (BLE <->UART),i need a faster rate in ble , and i found a way in the zone,that to use BLE_EVT_TX_COMPLETE to send data, the send...
I would like to use the A/D converter to monitor the battery voltage and need to know if the 0.6V reference is generated with a bandgap or some sort of divider network.
...
Hi,
Next problem I've experienced is jumping processor to Hardfault state at sd_ble_gap_adv_start
with whitelist and BLE_GAP_ADV_FP_FILTER_CONNREQ .
In case adv_params...
Hi
Although I followed and got working eclipse Mars on win10 using this great @Vidar tutorial I am still having problem creating a new project under eclipse for any of...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am developing a power aware TWI driver for 51822/422. All appears to work properly except when I simulate a bus fault by shorting SCL to ground or shorting SCL and SDA together...
Hi,
Firstly a warning I'm a noob in this area.
I'm seeing some strange events consistently returned from the nRF8001 over SPI. I have an example of the SPI traffic below...
Hi! I would like to get adc sample from two different channels at the same time on my beacon (nrf1822), using the same interrupt. Is that possible?I mean I can use ADC_IRQhandler...
Hi,
It's a very simple question, is there a simple way to check GPIO pin status. I just want to know at a given time if the Pin is High/Low. I don't think I need an ISR...
Hi, I just started working on nRF52 with Bluetooth, and I have some concerns about DFU and security.
I’m working on a product equipped with an nRF52 and a MEMS microphone...
Hi!
I am using the NUS service and I noticed that Android 6 (Marshmallow) will not go faster that 47.5 ms. Even iOS can go to 30ms. My target is 7.5.
Am I doing something...
Hello,
I am using nRF52832 with S132 and SDK_11.0.0. I am facing issue with using power fail warning POFWARN. below is my code snap.
void POWER_CLOCK_IRQHandler(void...
Hi All.
I'd like to know how to turn off or on shockburst feature.
After I set auto ack & retry count, Tx successful interrupt occurs, even though receiver device is in...
