why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
Both examples were built failed in Keil due to exceeding 32K trial limitation. Is there any way to reduce the size? Or any suggestion?
Platform: nRF52DK
Keil uVision...
I am working on a project using a BLE Nano and Nordic sdk 8.1. When I compile my application and flash it to the device my program runs exactly how expected. If I unplug the...
I use the nrf52832.
In the beginning,I can download the code and it works well.
And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
I use the nrf52832. In the beginning,I can download the code and it works well. And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
Hi, i'am working on a custom board on which there is two led drive by a led driver.
The two leds are wiring to be drive by pins P0.14 and P0.15, but unfortunately these...
Hello! I am using a nRF52832 device, along with SDK 12.1.0 and S132 v3.0.0. Data is being sent data through BLE and received on an Android phone.
After some tests I noticed...
I need to have a Central device physically connected (via UART) to a sensor. Data is collected from the sensor and sent to a number of Peripheral devices which use the data...
Take a look at these screenshots. With the trigger enabled, the average current consumption is reported at 13.21uA. With the trigger disabled , the average current consumption...
Dear Nordic,
I want to know if it is possible to send asynchronous data type from a slave node to a master node (master node would be in continuous scanning mode). Reading...
Here is my problem. I want to disable uart when there is no data coming into MCU.
I used IO LotoHi event to enable uart Rx. After finish data receiving, I disable Uart.
...
I've modded the PCA10040 DK for current measurement with an ampere-meter (TTi 1604), using a program which turns an LED on and off every 5 seconds. The measured current stays...
I am using an LG G5 and my co worker let me use a google pixel. I tried using the s132 softdevice along with the BLE UART example code from 12.2.0, I get the device is not...
I'm aware of GATT's Profile, Service and Characteristic.
And also, for GATT_Server, GATT_Client it can be Central or Peripheral. (As I manually set it.)
And also, the...
hi
I am using nRF51822(from waveshare). previously i was able to program my device with nRFgo Studio. But I am facing a problem now. I programmed my device with radio transmitter...
