Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
The user manual only tells information of pins , active low such things of led on nRF52832 Dk. There is no detail information of components on nRF 52832 DK board. So, can...
After reading the FAQ on DFU I still do not understand how the bootloader and SD DFU are performed so that a failure during the upgrade does not brick the device (see answer...
Hi,
I have some queries about ESB RF Communications.
1.The address : is it possible change RF communication to one node(Tx) to multiple nodes(Rx). If Yes, Where can...
Hello,
I found that after using SPIM I have forever additional over consumption (additional 400-500uA).
It was solved here in forum
And there is errata 89
[edit]...
I use Gazell to acomplish one host --two device.When i just have one device,everything is OK。But when added to two,it cannot work.
I think,whether channel of two devices...
Hi, I am looking for the test report on the bluetooth emission of the NRF52832 that we use in our product. Could you send it to me by email? Thanks,
Emeline
Greetings,
I have been using the nrf sniffer and Wireshark successfully for for the past month or so. Today Wireshark stopped filtering for the device(s) selected in nrf...
Nordic Team,
I was hoping you could create a similar post to devzone.nordicsemi.com/.../ but one that was dedicated to possible improvements and feature requests. This...
Do you have any recommendations on measuring the voltage of a lithium battery (e.g 4.2V) using nRF52?
Obviously you can't measure directly as Vbatt > Vdd.
To use a simple...
Hello,
I am working on ble characteristics tutorial. (F00D, BEEF example)
I flashed the program and tried to scan my nrf52 DK on my Android phone.
Some parts of my Android...
I am designing with nrf52832 and experiencing some connection issues at 0C. The system gets disconnected every few seconds with 32k crystal, but no issue with RC oscillator...
Hi,
We want to upgrade our product from SDK9 to SDK12.
I already check the below questions.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi...
Hello!
I have
uint32_t adc_value (from external ADC converter)
And try to send it value through ble. My code:
main.c:
....
for (;;)
{
Weighing();
power_manage...
