I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
Hello.
How to write custom firmware updater, which:
Takes new firmware from other device on SPI or I2C bus.
Writes it to flash ("bank1" at 0x1B000, or...
Hi;
I'm studying on SPI communication at nRF51822 (not DK) but i could not find the pins for spi communication, i read at somewhere SPI is only used at DK(developer kits...
hi
i'm using the nrf15822 beacon for an application of communication on arduino
I just would like to understand how i should start to stream my data using the beacon beacause...
Hi all,
I am using S130 in scanning mode and I would like to list the devices that are currently advertising by their friendly name. I have access to p_ble_evt via BLE_GAP_EVT_ADV_REPORT...
Hi,
I usually use electronics.stackexchange.com/.../15143 approach for decoupling capacitors and until now I had much better EMI performances.
I make sure that tracks...
We would like to reduce the attribute table size a little to increase free RAM. Are there any guidelines explaining how we can judge how large the table needs to be for a...
I compile SDK7.2 example hrs in "experimental_s110_with_dfu" by eclipse,
and I download softdevice & bootloader by nRFgo
then i use master control panel to DFU the hex which...
In the nordic documentation it mentioned that in the init packet we can write list of supported softdevices so that if one of that matches it will start the dfu. But in Signed...
