hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
when i use nrfjprog.exe download my application code,Change nrfjprog.exe --eraseall --program ble_module.hex --verify --reset to nrfjprog.exe --eraseall --program ble_module...
My apologies, but I just want someone to give me a quick brief on what are these things and how they work. AFAIK, the nrf51xxx series SoCs render limited, sporatic radio availability...
Hi,
I am Working on a BLE application in which I do not want to expose certain services until I am securely paired/bonded to a valid device. The problem is that during...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
I'm using the nRF52 + SDK11.0.0 + s132 and the ble_hrs example. The function conn_params_init() is called to initialize the connection parameters that the peripheral will...
Is there a way to pause all peripherals when hitting a breakpoint? In particular, I would like to freeze the RTCs when I hit a breakpoint. My app wakes up once a second, and...
I`m trying to operate PWM and soft device at the same time.
I have to make 4 Mhz using PWM block so I checked the PWM driver. There is no problem when using peripheral/pwmdriver...
Hello there.
I´m using a Taiyo Yuden evaluation board with a nRF51422 to connect with 3 different sensors. In addition to that there are also 2 buttons connected to the...
I am working on a BLE peripheral. I have a large, variable length characteristic I need to set from the central.
When the central is the BTool, I can write up to the maximum...
I'm using the nRF52 + SDK11.0.0 + s132. I started with the ble_hrs example and modified it. I now want to make the service/characteristics use proprietary UUIDs and I'm following...
I have been having issues with bootloader launching my application on a custom nRF52832 based hardware device.
The bootloader itself seems to be successfully completing...
