Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
When my program was running,An error occurred.The program ran here
（app_error_handler_bare）and the error_info is
0x00000004, how can I find out the reason of error_info...
Hello,
I was trying to build Clapp oscillator with a JFET J310 (FYI: link text )as it is shown in the figure.
Capacitor C is variable and goes from 20 pF to 285 pF...
Hello
Please tell me about sd_ble_gatts_value_get ().
Please tell me about sd_ble_gatts_value_set ().
For these two cases, it is not used in the SDK, but is it old?
Please...
Hello together,
I' am working on a Bluetooth application and have a problem with the transmitting time of the Bluetooth.
In this Screenshot you can see the end of...
Hi,
I want to connect an ADXL362 low-power accelerometer to a nRF51DK via SPI for a BLE application. However, I'm still quite unfamiliar with Nordic Semi's BLE offering...
In SDK12.2 init timer user APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, true);
but when I want to use more timer,how can i add the number?
Dear Nordic,
I am having some apparent delays in the time that passes from the pressing of a button, and the execution of the ISR that this button triggers. I am using...
Hi， Nordic
I checked DFU operation, found DFU work in bootload mode.
I want to know below operation is OK or not. Plz help me check:
download DFU bootloader
download...
Hi, I use the PCA10040 v1.1.
This is an example of a PCB stack-up.
My questions are,
In the case of PCA10040, which is 4 layered, what are the values of...
Hi,
I am writing a firmware for one of my custom boards which use GPIOTE to detect interrupt for 3 GPIOs inputs (P0.03, P0.06 and P0.09, both with internal pull-ups) and...
Hello,
I'm trying to write my ADC samples over spi on a sd card (Using SAADC like in the sdk 12 example with PPI and using fatfs like in the example in the sdk).
I open...
I have been using the pc-ble-driver Python bindings to implement a peripheral. I have extended BLEDriver to support sd_ble_gatts_* the functions. I now have a working peripheral...
Hi All,
I am struggling with this question from many days. Does the SPI transmit or receive operation in SPI master code uses DMA? While using SAADC DMA I have specified...
I'm using an app timer to blink an LED while in the bootloader.
Initially I was configuring an app timer when the bootloader started up and never stopped it, assuming the...
After failing in replacing a Cortex M4 for a NRF52832 I'm studying the possibility of using a NRF51822 as a BLE controller, used by my Cortex M4 MCU.
As I saw there is...
