I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I have a BLE device that listens for a connection - upon opening a connection with a smartphone and switching advertising status to non-connectible - it receives some data...
I use nRF51 DK and soft device s130.
I nedd to add a file ("app_uart_fifo.c") in the example of multilink central, after i add the file i build the proyect but the files...
To confirm this link text .
I want to know how to run raspbian-kernel v3.17.4 .
Is there rasbian image including kernel v3.17.4 in rasbian images site ?
Hello,
There have been some questions on the forum regarding the DFU and it's zero value for the application CRC. However, none of them seem to address this question so...
Regarding the radio peripheral, I stumbled upon these 2 properties and have no idea what they are for.
What's access address? And what is a channel? Shouldn't there be...
I am runing ble_connectivity example with simple_uart instead of app_uart was not working unable to scan not getting advertisement reports.
Its been working with PCA10001...
Hi,
I have a pretty simple problem but I can't get it right. This is what I want to do:
T=000, PIN_x = 0
T=004, PIN_x = 1
T=100, call a routine
T=543, Start over...
Hi,
In the BLE_UART example code posted here , I noticed a discrepancy with the SD 3.0 migration document, SDK12, and the example code.
In stock SDK 12.1.0, ble_stack_handler_types...
Hello everyone, i need some help and suggestions in understanding what is exactly happening. I have read a lot about bugs and workarounds in pstorage and now i actually don...
Hi, when reading radio transmitter peripheral example, I got stuck a bit on radio_configure(). I got stuck because I can only get some brief from the corresponding .h file...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
when i use nrfjprog.exe download my application code,Change nrfjprog.exe --eraseall --program ble_module.hex --verify --reset to nrfjprog.exe --eraseall --program ble_module...
