Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I have taken the S120 app, and am trying to have it connect to an external peripheral (not the provided S120 Multilink Peripheral app)
The S120 app successfully discovers...
I just received my mKITs. It is not the first product I have received and add keys into MyPage.
It just has a card that says to go int my account an add the keys, but I...
I am struggling to figure out why I can't write on the Peripherals memory to set a function. In this case I am trying to write in the 0x4000250C which is UART0, PSELTXD (Pin...
We have a project for a sauna controllunit,
A remotcontrolle and hostunit which controlles the sauna. The Device send comands to the host, the host sends Ack + Payload (the...
I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I was wondering whether bonding between devices is possible without using a passkey.
I found a good documentation by Nordic Semi which illustrates all the bonding...
Hi everybody
I've got a problem with my "custom hardware" with the "nRF51822 QFAAFA 1322AA" MC by Nordic. When I try to connect the hardware with the "Master Control Panel...
Hello,
I'm using GCC with the soft device 6.0.0. I'm having this reoccurring issue where sometimes I will start to debug and the execution flow will get stuck in some kind...
Hi,
I catched the air data packets by Sniffer and it shown that there was an error, MIC incorrect, which could be seen as followed, and the whole packet was malformed....
Hi!
I have some problem to reconnect an already bonded device containing a chip nRF8001 rev D with my iOS app. Rev C works fine with the first connection and the reconnection...
HI,
I want use some GPIO to detect "pin_high_to_low" or " pin_low_to_high".
and I think the "app_gpiote.c" might be helpful.
but I have been confused by function " sense_level_toggle...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
