I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hey guys,
I followed this guide and successfully synchronized the timers from two devices(nRF52 DK). But if I let these two synchronized devices keep running all the time...
Hi,
As stated here :
After manually starting the HFCLK
crystal it will be enabled even though
there are no peripherals requesting
the HFCLK. When no peripherals...
Hi,
I have my 2 nRF51 running with S130 v2.0.1, one is the central and the other peripheral.
I am transmitting audio data between both and want to reduce the current consumption...
Being a person with a poor name memory, I am really frustrated with the nRF SDK's naming conventions. For example, let's take a function
bsp_btn_ble_on_ble_evt()
Is...
We are using nrF52 series in combination with v3.0.0 of the S132 SoftDevice stack. And I want to understand if we have to go through any of the qualification certification...
Hi,
i got a random disconnect and cant find the cause.
I found this post devzone.nordicsemi.com/.../ and tried to folow the procedure.
I have set up breakpoints wherever...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control the onboard led that uses the methods LEDS_ON and...
I am using the nrf52832 with its Development kit to transmit trough UART to the PC a frame with 20 bytes, I have configured the port to 1MBoudRate. I have enable the flow...
I spent some time trying to work out why generating a private/public keypair in my application with the ECC module was failing due to an 'internal error' and had to eventually...
Hi,
In 868 Mhz band NRF905 supports frequencies 862.8Mhz, 868.2Mhz, 868.4Mhz and 868.8Mhz. The datasheet shows mapping of those frequencies to CH_NO.
In India only 865Mhz...
Hi,
I am currently working with two nrf52 boards in a serialized configuration.
I wanted to add the PA and LNA pin toogle on the connectivity chip.
As the gpio can't...
sorry, i tried "Getting started with the nRF5 development kit" tuturial about 3 hour.
but still not working for me.
stock at begining.
I downloaded nRF5 SDK 11
and...
Hello,
We are using nRF52 in serialization mode.
In the nRF52 connectivity chip side, we are using the example 'ble_central_and_peripheral'.
In the application chip,...
I would like to use the nRF52840 for 802.15.4 but it is rather vague in the OPS as to how to do this. I can figure some of it out but not other parts.
It mentions "assisted...
