My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
Hello!
We are using a custom hardware design based on nRF51822. Recently we switched to the new chip version QFAAG0 with softdevice 6.0.0.
Our application needs a repeating...
I have tried HTS(Health Thremometer Service) sample Program on nRF6310, PCA10006, SEGGER J-Link Lite and iPhone5C.
First time, temperature is displayed on the iPhone5C...
Hi,
I have a custom board with nRF51822 chip on it and tried to run the proximity sample program on it. I have used the nRF51822 develpment board + nRFgo Motherboard to...
www.dropbox.com/.../Screenshot 2014-04-03 11.41.25.png
I guess has nothing to do with crc16?
the call stall seems unreasonable, is it because my stack is messup?
...
Hi,
Is it possible to control the drive current of the gpio pin?
Can anyone explain the different possible drive configuration for gpio's (S0S1,H0S1, etc..)?
Regards...
I'm trying to compile the bootloader for gcc from this post: devzone.nordicsemi.com/.../nrf51822-over-the-air-bootloader-with-gcc
The bootloader start (I can find my device...
Hi,
I'm confused with the functions (sd_power_mode_set and sd_app_event_wait).
1.I think there are described with the same function.I can't tell the difference between...
Hi,
I've developed an application and tested it on the evaluation kit. Now i'm trying to run it on a custom board with a nrf51822 chip on it. I've made modifications to...
Hi,
I use to the nrf51422 with nordic's dev/ev kit.I want to build a project and the purpose is to get the sensor's date and use the ant protocol to deliver the date to...
Hi,
i need some help by selecting the right Hardware for a new Project.
I want to build mesh network so i think ANT is the right Protokoll for me, with BLE i can't build...
Hi
I have a BLE module of nRF8001 chip and everything is working fine with it.In your Arduino compatible libraries for nRF 8001 you have a function hal_aci_tl_init() in...
