Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I have a vendor specific characteristic for the battery voltage in my device, expressed as an actual voltage rather than a percentage. Values are 0.000V to about 4.300V and...
HI,all!
I recently using pstorage to store data
and the pstorage_store(); funtion always returns NRF_SUCCESS, but never triggle the cb_handler, is that normal?
by...
[environment: s110_nRF51822_7.0.0 + SDK nrf51_sdk_v6_0_0_43681 + PCA10000(QF AAG0)]
I failed to get pstorage working in my own code, then I picked up the sample code from...
My NRF51822 die. When connected, keil can't download or erase flash. But it can be found by SW port when I just power on, then it almost be unavailable at the same time. ...
Hi,
I am trying to use the RX interrupt on the PCA10001 board, using UART0 for wired communication and S110 (s110_nrf51822_5.2.1) for Bluetooth LE communication at the...
Hi, i'm trying to communicate between a msp-430f5529 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
Hi there,
I'm currently facing the problem, that an example as simple as
volatile float sum;
extern "C" int _start()
{
float a = 1.0;
double d = 2.2;
sum = a ...
I have a nRF51822 mkit board which I would like to use as a BLE peripheral to connect to my linux computer with BlueZ. I would like to be able to have a simple GATT connection...
Hi,
I'm trying to get a SPI based peripheral going without much luck.
One thing I noticed, in the debugger, is that on my implementation the field spi_base_address->POWER...
Hi,
I'm getting problems on the pca10001 uart example. I get the "Start:" string on the terminal but it can't echo what I type on the keyboard. Another thing is that I...
The nrf51 powerdown examples
github.com/.../nrf51-powerdown-examples.git
Are these power down examples are helpful. They clearly indicate how to power on the nrf51822...
I have a custom board using the nRF51822 as a peripheral with the S110 SoftDevice. The centrals are mobile apps, both Android and iOS. The device spends a lot of time in a...
Hi
I'm trying to run uart example on nrf6310.
I followed following link.
devzone.nordicsemi.com/.../
and I defined ENABLE_LOOPBACK_TEST.
it was resulted in blinking...
I am using sd 7.0.0, I have a simple bootloader implementation that follows the bootloader sample code pretty closely. When I jump to my application from the bootloader and...
Is there anyway to get a light to blink using only the PCB antenna module?
Also, is there anyway to blink a light using only the Bluetooth Smart Beacon chip?
