Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
In my application I have to advertise and scan, I know these two actions are multiplexed and there are no problems when there is no BLE connection (I use s130, sdk 9.0.0)...
Hi all,
I'm developing little project on nrf51 dongle(pca10031). After few succeses now I have big failure which stops my work.
How my environment looks like: Ubuntu...
I built the GCC bootloader from source based on the suggestion of another user in this forum instead of using a precompiled hex file. The Softdevice is 7.1.
It shows DfuTarg...
I have a min connection interval of 200ms and max of 250ms. I have set slave latency to 10. These parameters are set both on peripheral and on central. Still, after connecting...
Hi! I am working on a project that uses the Multilink example. On the client (nRF51422 w. SD 120) my program crashes and starts the main loop again after a few seconds. I...
Hi,
I'm developing a device that will be powered by two AAA alkaline batteries.
Since the operating voltage of nRF51822 is 1.8 to 3.6V I was considering to connect them...
Hi,
the example ble_app_uart_s132 from the SDK 0.9.2 is not longer working with the new release of S132 ( s132_nrf52_2.0.0-7.alpha). I had to go back to s132_nrf52_1.0...
My setups are:
RBL BLE Nano
nRF51_SDK_9.0.0_2e23562
Keil uVision V4.74.0.22 or gcc-arm-none-eabi-4_8-2014q2-20140609-win32
My design is to advertise a manufacturer...
I'm using nRF51422 with SDK 9.0.0 and S310 ver 3.0.0.
First, I program softdevice and dual bank bootloader by nRFgoStudio. After that it is possible to program my application...
Hi all,
first of all thank you for such a great knowledge base and community exchange.
I am pretty new in the development for nrf51822 devices.
I managed to run the...
The comment above app_button_init says, in part:
* @note Normally initialization should be done using the APP_BUTTON_INIT() macro
This macro is also mentioned in the...
I'm using the s130 SoftDevice on the nRF51 dongle and writing a PC app in python. How can I declare an int8_t in python for use in the sd_ble_gap_rssi_get function? The function...
Hello there, I am already guessing that by the question alone it seems like what i'm asking is silly or wrong but I have no formal education here so I will need some help...
Hey guys,
I'm building a remote control (similar to TV remote) and I'm using nRF51. I am trying to figure out optimal connection parameters so the battery would last as...
I am using nRF51 SDK v10.0.0 and running simple_uart application on nRF51822 Evaluation Kit(PCA10001).
Added CFLAG += -DBOARD_PCA10001.
after flashing with nrfjprog...