Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
I would like to implement a simple wireless sensor network, using Enhanced Shockburst with Auto-ACK. The idea is that there will be many sensor nodes (SNs) reporting to one...
I have a question about using the GPIOs,I found that I can set a ‘1’ at the same bit position of OUTSET register and OUTCLR register. But which one is effective ?
Hello guys,
Looking through the product specification for nRF8001 I am still not clear on whether a master device can be connected to the nRF8001 (in peripheral mode) and...
Hi,
When erasing one page flash for responding one GATT request, it always went into assert_nrf_callback and has to reset the app. So I have to disable SoftDevice before...
Hello,
I am going to start programming BLE application, and I would like to know which enviroment is best to program it. Are there too many differences between programming...
Hello
According to the documentation the optimal CPU frequency is 16 MHz, Please, could someone tell me if that is correct or not?
Thanks for your help
Hi,
I modified the ble_app_hrs sample application with one custom service which includes, some custom characteristics (128 bit uuid), Now the problem i am facing is, i am...
Hi,
How to implement the passkey authentication, we are using nF51822 evaluation board. Is it possible to display the passkey using master control panel? And, we also don...
Howdy,
In a similar vein to my recent question about production programming....and nothing to do with takign an nRF51822 out for a walk :)
We'll write a simple test...
Hi
Before, TX and RX functions run well at iOS6. After we updated to iOS7, RX still worked but TX couldn't send out data. Did you verify nRF UART app at iOS7?
I'm reseaching a tag in low energy-cost using the nRF24le1.Till now,I can receive the message from the tag successfully, but can't send the command to the tag to read or write...
hi,
Now,my pre-Develop product(BLE),that to measure the Tx transmit power not correct with my setting(default 0dbm).
so,i have program a project for to sure the reason(Hardware...
I need to connect an I2C/TWI device to the nRF51822. The I2C device is running at a fixed 3.3V (from a boost DC/DC), but the nRF51822 is powered directly from a CR2032 battery...
Hi,
Is there anyway to keep the RTC going while in reset, device sw has crasched or in powered off mode or would I need an external RTC for this?
Is there any possibility...
