Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm running one advertiser and one scanner at the same time, and I want to change the data inside the advertise packet, every advertise. Looking at the forum and...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi all, Now I'm working secure bootloader in sdk12 for these I installed the nrfutilv1.5.0 by following nrfutil user guide
link text
while I'm creating .zip files it...
I've seen similar questions posted, but none that match my situation exactly and those solutions did not work for me.
I'm using the pca10040 dev kit, which I connected...
For the radio peripheral, if I use a shorts (shortcut) from END to DISABLED states, is EVENT_END still set? Because I enable an interrupt on EVENT_END, but not on EVENT_DISABLED...
Does anyone know how to remove all Nordic software and clean out all registry keys?
Installed mastercontrolpanel.3.9.0.6.x64.msi and all is working great with the RF Dongle...
Hello together,
i have a question to the uart hardware communication.
I try to send 6 bytes from the nRF51 DK, S130, SDK12 (p0.09 tx) pin to another hardware rx pin.
...
Hi,
Trying to add DFU service on the new SDK, but when compiling getting this:
compiling nrf_dfu_flash.c...
..\..\..\..\..\..\components\libraries\bootloader\dfu\nrf_dfu_flash...
I'm using SDKv12 S132v3 on nRF52 peripheral device. I have characteristic with following security setup:
char_add_params.read_access=SEC_JUST_WORKS;
char_add_params.write_access...
Is it possible that a crash in code can prevent connection by SWD to an nRF51822?
As I had an instance this morning, where after uploading, some code to a smart watch,...
I'm trying to use a 32 bit service UUID, but it doesn't seem to be supported by SDK 10 or SDK 12
Looking in the HRS it has this code
BLE_UUID_HEART_RATE_SERVICE, BLE_UUID_TYPE_BLE...
Hi,
I am using App Timer for measuring time and at the same time while loop to check if the timer reached particular time.
I have noticed during while loop App Timer...
Hi,
I'm using bootloader from SDK v7.2 When the application jumps to the bootloader (through NVIC_SystemReset), the call sd_softdevice_vector_table_base_set returns SVC_HANDLER_MISSING...
