I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I would like to have a ble communication between a keyboard and a computer. The keyboard will be connected with a nordic chip, but what can I use on the other side?
Do...
Hello,
I found this on the forum:
According to nRF51822 PS v3.1 section 8.23 pullup and pulldown resistors have a typical value of 13kohm. if you have e.g. a button...
Hi
I got a new chip, marked as "QFAABA / 1542AB".
I see that both errata versions 1.1 & 1.2 seem to be relevant.
Can you tell me which errata should I refer to?
Thanks...
Hi Nordic,
I am adding pstorage capability to ble_app_proximity example. Before adding pstorage, the example could receive Immediate Alert from a central and set on/off to...
Hi i'm a newbie in nordic chip. Can someone please explain to me that how to enable and configure the timer interrupt and what kind of setup need to be done?
Example in...
There is a mistake in LEDS_INV_MASK definition:
PCA20006.h / nRF examples 10.0.0
#define LEDS_INV_MASK 0x11111111
// blue will be erratic
PCA20006.h / nRF examples...
Hi,
when i setting up a new project in uVision, i get a crazy Error wich i cant handle with.
My error is --> main.c: error: C3906U: Malformed via file '.\main.__i'....
Hello,
in the new version of sdk (11.0.0) you support s130 only.
That means the code contains both peripheral and central implementation.
Does it mean that s130 consume...
The following seems to suggest each write event can only contain 1 byte of data at a time.
/**@brief Event structure for @ref BLE_GATTS_EVT_WRITE. */
typedef struct...
Been playing with NRF24L01+ for a while and mostly they work as I expect. Now, I'm trying to use an ACK payload, but whenever I try to set up the receiver to put a payload...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
