Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Peer manager worked fine for bonding on my pca10040 board. However, when I flashed the code to my prototype, built with a SparkFun nrf52832 prototype board, I received PM_EVT_ERROR_UNEXPECTED...
Hi team,
Iam using sdk12.1.0(ble_app_beacon and ble_app_hrs_c) , i modified the advertising data and sending to other end.other end one scanner is receiving the data .but...
Hi,
i am beginner to Nordic i want to work with MMA8652FCR1 using NRF52 DK board is there any example to understand What is TWI and How to work with it. and also how i can...
Hello to all embedded Jedi Knights!
I was wondering, how could I read the CTRL-AP's APPROTECTSTATUS register (of an nrf52832) using the J-Link commander.
I know that...
What are the states of the bi-color LED (LD5) on the DK?
I'm aware that solid green is enumerated and 10Hz blinking is not enumerated (or power-only). Do the other states...
Hello,
i decided i will use a nrf52 3rd party module for my project cause i want to skip Qualification Process and Bluetooth RF-PHY test.
I haven't seen any 3rd Party...
nrf52DK - SDK12.2
This is probably a simple thing I am missing but I can't seem to find the answer.
I have been following the tutorial for BLE Characteristics ( here...
Hi,
I am working with a nrf51822 and I have seen that the way to wake up from System Off mode is by a GPIO interrupt. I wanted to know if it is needed to configure previously...
I am a new to the uVision4 and having trouble with the 51822 evaluation kit demo.
I am able to build the ble_app_hrs demo and can load and run it using the Flash / Load...
Hi
I'm using fs_storage function to read and write in flash memory. Value successfully stored in evt->store.p_data but after power off it value become 0
switch(evt-...
Hi, I'm using a nRF51822 as a observer/scanner for Eddystone beacons. This device is intended to scan up to 16 beacons, but under certain conditions (unknown at this moment...
Hello,
i use a nrf52 developpment board, with the SDK 12.1.0. I use the ADC example which use the ppi channel, my question is : it's possible to set the ADC driver without...
Hi all,
i try to log event in memory, and when connection is established read value from E2C and send to APP.
if i send characteristics when event BLE_GAP_EVT_CONNECTED...
I use the ble_app_proximity example of the nRF51_SDK_10.0.0_dc26b5e, the chip on my board is QFAAH00 . When I down load the code, it pops the windows "IAR Warning: Stack pointer...