Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I'm currently using an application that needs a very speed detection of GPIO and need to use NMI on GPIOTE.
I tryed to find how can I connect my NMI to GPIOTE but...
nrf_drv_usbd_init() calls nrf_drv_clock_hfclk_request(NULL)
however nrf_drv_usbd_uninit() calls nrf_drv_clock_lfclk_release();
Is this correct?? If so why?
Hi, I have the opportunity to bid for some research funding for my project, and I'm thinking of speccing a workstation for processing video in realtime, and sensor data in...
I am trying to add the heart_rate_meas function to the ble_app_uart project.
Is this plan possible?
However, it does not go well.
Why are you concerned with this method...
Hey Guys,
im working on some sort of application transport layer for ble and have some questions to better plan what i need and what is kind of redundant.
Is it correct...
Hello everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
I'm using nrf52 with SDK version 12.0.0. I'm trying to use the FDS for my application. I used one of the existing fds example from link fds_example .
With this example...
Hello,
I am a bit lost, after concluding the application part of my project I try to approach the ble part.
I read the "Getting started with bluetooth low energy " and...
Press down PWRON1 give rise to Q2 and Q3 conduction, the 51822mcu power on and IO send a hight level to PWRON,to keep VCC_nRF.
At this time press a lot of button will not...
Is there an unsecure version of the bootloader? I'm looking for something that will take anything as an upgrade.
I figure if I'm stuck in the bootloader anything is better...
I want to set up a rPi3 as edge router for 6LowPAN over BLE. Ideally I would like to have random devices (users) come and go by dynamically connecting to the router. Same...
i am using eclipse IDE. while flashing my code to nrf development kit it is showing like this and also in the console it is showing that flashing is done.
console:-
SEGGER...
Hi
For new BLE project we planing to use slave that allow few (3-4) connection at the same time. i.e After the master (phone) connected to our slave, the slave continue...
