We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello.
I use the BLE multilink central example to connect to 2 sensors. I changed the example in that way that i successfully connect and read data from a Wahoo Cadence...
the application is examples\peripheral\csense , cap sensor can sense my touch, but when I cover a 1mm acrylic on the cap sensor, will not sense my touch.
so I want to know...
Hi ,
We are using BLE nano board as a connectivity board and mDot board as application chip which is running on mbed platform.Connection deatsils are same as described here...
Hi,
I am working in one application in which I need SAADC to sample two channels at 1ksps and 500 samples per seconds.
I am sending 1 and 2 to switch the sampling rate...
After trying to run keil project after setting conditional breakpoit it raises error.
is it right that nrf52 doesn't support conditional breakpoits? or something wrong...
Hi,
I'm using the SDK11 and SD130 on a custom board which has a nrf51822.
I connected via SPI to a DSP that sends and receive audio.
My handler of the SPI is as it follows...
I'm trying to send a set of 246 bytes by uart fifo. I have a PC side which retreive the data, but I always miss some bytes (4 to 6).
I'm checking app_uart_put return and...
Hello,
I would like to use the nrf51822xxaa as BLE gateway for an ARM application processor (connected through the UART).
I successfully cross-compiled pc-ble-driver...
Hi..
Can i use both observer and broadcaster roles concurrently in s130 soft device..?
Is any TDMA needed to do this..?
Is it possible to do without stooping the other...
Hi,
I have read the S132 Softdevice specification v3.0 and just want to make sure that my interpretation is correct. There are two scenarios I would like to verify:
...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
When...
Hi,
As a beginner, I'm trying to have CDC J-Link Uart port work with my laptop. I'm using nRF52 board. When connecting the board to my laptop (windows 10), it displays...
Need some help on the tcp server example in the IoT SDK.
All steps working but the python script gets Connection refused.
bash# ifconfig bt0
bt0 Link encap:UNSPEC...
(nrf52832 PCA10040)
Hello. I'm trying to go along with the ble tutorial (advertising, service).
I download before last version of sdk 11 because with last 12 it's not working...
Hello everyone,
I have 2 chip; Bluegiga and nRF51-DK
I can easily advertise my custom service in Bluegiga chip. As you can see, nRF Connect application shows my service...
