Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
We are using a MMA8452Q accelerometer connected to an nRF51822 via TWI using the twi_hw_master. Reading the WHO AM I register is the first attempt to get the TWI running but...
Hi,
let's say I program flash with SD, Booloader and merged App1&Ap2 images. I need to switch application (only once, after some self tests) using some command from application...
I am having an odd problem.
nRF52
softdevice S132 V2.0.0
I have a bootloader and application. when I program them directly to the device they both work fine and can...
I need to get three ADC data from acceleration sensor with nrf51822. I tested getting a ADC data using simple_adc_pca10028(Keil_v5/ARM/Pack/NordicSemiconductor/nRF_Examples...
Hello
We are about to move an old design based on the NRF51 to the more powerfull NRF52.
In this context we would like to use some of the new API’s that has been introduced...
Recompile dfu_dual_bank_ble_s132_pca10040 example from SDK v11 with softdevice v3.0 header. DFU is advertised, but not able to connect to it. always timeout,
There are three...
I made a product with nrf51822AC(based on SDK6.1&softdevice7.3), now we want to do BQB testing and I am working on our board's DTM code.
I have tried example "\Nordic\nrf51822...
Hi Nodic:
I use the PCA10028 V1.2.0 board , and use "nRF51_SDK_9.0.0_2e23562" SDK, ..nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_uart\pca10028\s110\arm5_no_packs...
Hi,
In SDK11 I was able to update advertised device name without restart, just handled write on the characteristic and update advertising data (through a second call to...
I'm going through pin_change_int example and can't understand how we tell controller where locate the function for our event.
Probably it occures in channel_port_alloc that...
I'm trying to communicate with an EEPROM chip using SPI. When I run under the debugger, the EEPROM doesn't respond; without the debugger running, it seems to work fine.
...
Hi everyone
I am working with nrf51822 sd 110 v.7.1
If I change from XXAA to XXAC, do I have to change the IRAM settings? If yes, which are the correct settings?
...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
I think similar to but not exactly this question: devzone.nordicsemi.com/.../
Can I get a quick clarification here....
I'd like to encrypt the zip data / application...
