Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
SDK v8 release notes specifically state that there is no S310 support. Are there plans to support the S310 soft device in future SDK releases or are you discontinuing the...
Hi,
I do some test for nrf51822 power consumption.result as below:
my board
1.system off mode:270uA
2.system on sleep mode(no UART,no GPIOTE):300uA
3.system on sleep...
hi -- i'm a big fan of the NRF24L01+ chip, i've written a high-performance driver for it using most of the features, relying heavily on Dynamic Payload and Auto-acknowledgement...
Hi
I'm trying to program a nRF51 DK (pca10028) with the heart rate demo "ble_app_hrs_s110_pca10028", but for some reason it doesn't respond... at all.
I started off...
Hi Team,
I would like to implement a second bootloader to program an external serial Flash chip.
Currently using S110 V7.1.
My current thinking is to create another...
Hello--
I have an NRF51422-DK devkit (PCA10028, v1.1.0) and noticed that pin P0.31 is not brought out to the connectors or mentioned anywhere in the nRF51-DK-HW schematic...
hi all
nRF24L01+ ???
as the data sheet wrote the support life :These products are not designed for use in life support appliances
what is mean this sentence ???
does that...
When I try to make a custom service with the S110, how do I set the service and characteristics up to use a custom 128-bit UUID instead of a 16-bit one, based on the Bluetooth...
hi Guys pls HELPPPPP
I have developing active rfID tag using nrf24L01+ and ATtinny13A, the program code is done perfectly, firstly I start developing the tag with separate...
Issue is related to:
devzone.nordicsemi.com/.../
Now I use latest SD S130_1.0
So, I added to my service characteristic with notifications enabled. But during discovering...
Hello,
I have a development kit with the PCA10000 and I can comunicate with the PCA10004 for about 5/6 meters what is ok for my application but now I want to comunicate...
Recently I needed to add some functionality, so the software could monitor when there was a ble gatt read characteristic event.
In the addCharacteristic code I simply set...
Hi, We have used nRF51 DK for developing an application where we used USB to load/flash the program code. Now we are in Pre-production stage where we can use only the nRF51422...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
