Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Hello,
I'm trying to implement a DFU support into the application, and in order to learn how it works, I'm following the steps at the page developer.nordicsemi.com/......
Is there an easy way to find out the range of handles for a service which I added? Obviously the first one is the service handle, then you add characteristics and descriptors...
Hi,
While access sd_ble_gattc_write api, I got an error code 0x00000011. If I check nordic document for sd_ble_gattc_write error code, I can't find any error code with...
I would like to use nRF2460 in my project (Hearing Aid for elder people).In that I need to transmit the data from a mic/line in to >30 receivers within a range of 100 yards...
I'm using nRF51822 and i want to send a notification to the central to notify it for the changing of a characteristic value (major_value) after using the sd_ble_gatts_value_set...
I currently have a custom service emulating the batterey service. I have added an extra characteristic to recieve data from the central in the same way as ble_app_uart. the...
Like explained in this tutorial , on master control panel I do File-> Flash Programming and reprogram the dongle, which then turns on one more LED on the dongle. But, I still...
I'm using SDK 7.1, PCA10028 eval board, SD110, MCP 3.8.0.7
I've compiled and loaded the dfu_dual_bank_ble_s110 project into my PCA100028 board. It shows up in the MCP as...
Hey,
I use ESB protocol on nrf51822. I am using one Pipe currently I can achieve only 183 Kbps, I read that i can achieve 1Mbps data rate if we use ESB. I have few questions...
I understand that it is possible to set a static passkey on the nRF51822.
However, what I would like to do is handle the verification of the user-entered passkey myself...
Hello all,
I am completely new to BLE and would like to make a sensor network with nRF51822 ( 1x S120 as center node and 8x S110 as slaves) I have been reading the content...
I am trying to make my NRF 51 advertise forever till someone connects. I have based myself on the ble_uart example where it uses fast advertising with 40 ms intervals for...
Hi,
Last year, I heard that nordic semi will release a SoftDevice for central that supports mulitple packets per interval time until June, 2015.
For now, I guess s120...
My understanding so far is that the input buffer of GPIO is disconnected by default and we can keep it disconnected for saving power when the pin is configured as output....
Hello,
I just read this paper "High speed data streaming with nRF24L01 " where we can achieve 1.6 Mbps Data Rate in clean RF environment. I am currently using nrf51822 in...
