Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
After searching in forum, I understood that we cannot debug application with softdevice unless PRIMASK bit is set.
But in my application there is a requirement...
Hi Nordic
I am using GZLL to develop a prototype whereby data from sensors will be transferred to a Computer in a Wireless sensor network.
The idea is, when data are requested...
Dear all,
we want to use a nRF52837 for a developement project we are planning. We have been asking ourselves on which functional level the alpha Softdevice S132 for the...
Hello, i analyze the device manager routine (device_manager_peripheral.c) and in BLE_GAP_EVT_CONNECTED case you checking containing the device address in bonded table.
My...
I am working with nRF51822 beacons and an iOS 9 application that I am developing. I am testing on an iPhone 6. My application uses the CLLocationManager's beacon ranging functionality...
Hi,
I want to use the whole payload of the advertising packet. I decided to use the manufacturer specific data. BUt I cant´use the whole payload by myself. I get this payload...
dear all：
I use the spi slave mode. i have a question,pls help me.thanks.the questions as follow:
I want to distinguish instruction type, and then reply to the corresponding...
Hello,
I am working on nrf51822 SDK 9.0 and softdevice 8.0 . I got the application note to create a custom profile for SDK 5.2.0 and softdevice 6.0.0 in nAN-36_v1.1 . ...
Hi: We develop our program based on (nrf51822 QFAAG0 1403AL), I found a serious problem that our new IC is (nrf51822 QFAAG2 1415AF), and the old program can't run on it any...
Not sure where to post this...
but there's a minor bug in components/toolchain/system_nrf52.c, where NRF_UICR->PSELRESET[0] is being checked twice to see if a reset pin...
While ota dfu via nrf toolbox android app, it sends wrong (0x15918) image size in start packet, and also bootloader starts writing softdevice image at address DFU_BANK_0_REGION_START...
Hi! I want to make a BLE network with 1 master (nRF51-DK) and multiples slaves (nRF51-dongle). I`ll send differents commands from master to slaves. This is for home automation...
Hello,
I am writing an application using SDK version 8.1 where I have a pin using the PORT event in nrf_drv_gpiote library. I have a need to disable the event temporarily...
I am encountering a problem with GPIOTE PORT events on the NRF51422 in a custom design. The chip occasionally seems to be able to get into a state in which the registers are...
