Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi
I am trying to flash a new firmware into my device through DFU via the programming python script.
I use SDK7.2.0, and do:
ipy main.py -f c:\myproject.hex -a XXXXXXXXXXXX...
We are using the Nordic UART service for our product. Should we just use the standard UUID that the Nordic Uart uses or just generate our own for the product?
Thanks
Hi,
I'm working on an embedded system using PAN1026 bluetooth. I want to use the nRF APP to communicate with the bluetooth module. Currently I have:
Setup the...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
I'm trying to use the nRF52 preview DK from Linux. Could anyone provide the correct JLink commands for flashing both a standalone hex, as well as one with a softdevice?
...
I'm writing a build script for gcc for the nRF51 and I want to use the provided .ld scripts.
In SDK 8, those scripts were renamed from gcc_nrf51_XXX_xxab.ld to nrf51_xxab...
Hi,
I want read accel data from BNO055 sensor to NRF51 DK board, but SCL and SDA pins are 1 always.
My code is the next one:
#include "twi_master.h"
#include "twi_master_config...
I have existing design with I2C accelerometer on P0.1 and P0.2 (SDA/SCL). Don't need extreme data rates. Since examples of initializing on-board TWI don't seem to exist, and...
I am developing a tool that will be using the existing NRF51 dongle to run the S130 SD and it is being written in Python. There is no way to change any of these parameters...
Does anybody have a suggestion for a relatively low cost way to test the output power of a nRF24L01+ module? We make the modules (which are identical to the demo module) in...
Hi,
I am using the GPIOTE->PORT event to detect button presses and I would like to detect both button press and button release.
However, it seems like SENSE can only...
(this is duplicate with a support case I just opened... I hope that's okay.)
Hello, I am setting up a new laptop (our development machine caught a virus) and have installed...
Hi,
I have a sensor which sends data in a not specific time and each time start to sending data sends more that 100 data in 5 seconds
My problem is i just want one data...
Hello,
as described in the Compatibility Matrix it is necessary to use a revison 3 chip to use the S130 SoftDevice? Right?
Please explain why the Revision 2 chips...
I'm working in a project & I want to wake up the system from the sleep mode but it didn't wake up or I don't know what is expected on the wake up, will the system be run from...
