Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
Hello,
May I please check if the following is correct? On the nRF52840-PDK board (v0.9.3, 2017.47), the "VTref" pin of the "Debug In" header is connected to VDD. Should...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
I am working on a project where we are using a nordic bluetooth chip and connecting it to a RS485 Bus using UART with Baudrate 115200. The messages sent from the Bluetooth...
I want to experiment with BLE Mesh. I have several BLE400's with nrf51822's. I want to use these as mesh nodes. I want to get the nrf52-dk to use as an interface node. Can...
I recently downloaded Segger's Embedded Studio to compare its performance and ease of use with IAR Embedded Workbench. We have a kickstarter version of IAR for ARM which has...
hi,
i am using nrf5 sdk 14.2.0 ble_app_uart example with keil v5 IDE and i am doing coexistence with nrf5 sdk for mesh v 1.0.1 for nrf52832 mcu.
a have done all steps...
I use nRF52840-Preview-DK PCA10056 v0.9.3, SDK 14.1.0.
I would like update bootloader, but i have any problems.
I do these steps
1.eraseall 2.program softdevice 3.load...
May be I just did not fined a good reference manual for the software, but it really frustrating me to try and understand from examples.
Is there some guide which take a...
