I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
Dear All,
I'm trying to set a static passkey. I have created 2 custom characterestic. One characterestic is used for notifications and the other one for writing. For communication...
I'm making a peripheral device that should be powered off most of the time, but never idle if on, so I want to make sure that it is always (1) connected, or (2) advertising...
Now I have a project to build the schematic.
a, 5 LED indicators(0603) were driven individually by GPIO port directly, serial with resistor, then pull down to GND.
Is...
I installed nRFgo Studio Version 1.20.0.2 (which removed my older version) and was trying to program a softdevice (5.2.1) into our custom board and was presented with a popup...
Hello, I just received the nRF8002 development Kit and want to connect it to my windows 8.1 64bit machine. I get errors that there is no driver. Tried downloading the latest...
Hi, when calling sd_ble_gap_address_get from APP i get 0xXXXXXXXX4F and when i call it from DFU i get 0xXXXXXXXX50(X beeing the same), why is this? Is it a feature or a bug...
Hey Nordic--
I updated my Keil project from SDK v8.0.0 to v8.1.0 and immediately get some compilation errors due to redefinition of symbols.
In nrf_sd_def.h, I think...
Hi everyone. I have a strange problem. As we all know, there's a bug in SDK8.0.0 that dont allows to infinite advertising. To work this around i set advertising interval to...
Hi!
I am using nrf51DK with s110 soft device loaded on it to read data from Bosch BMA180 accelerometer using I2C interface. I would like to use clock prescaller and transmit...
nrf51x22_qfab_schematic.jpg I was going over the schematic and layout pdf files for the nrf51x22 before I began to create my own board and noticed that Pins 33 and 34 are...
SoC: N RF51822 xxAC
Toolcha in: MDK-Lite Version 5.15
Softdevice: S110
SDK Version: 8.1.0_b6ed55f
I'm using a custom board which is functioning well. The app is functioning...
