Hi everyone,
I’m designing custom hardware for my application using the nRF54L05 MCU (v2.9.0) . However, I can’t connect to the device from iOS — the connection always fails...
With the transition of the RTC peripheral on the nRF52, nRF53, etc series to the GRTC peripheral on the nRF54L, it appears there is no longer any low-power counter that can...
Hi all :
I am trying to use the nRF54L15 built-in load capacitor for crystal but I do not know how to measure the crystal performance, such as driving level and negative...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
Quick question.
Per the unique ID in chips from around a decade ago were not guaranteed to be unique.
I'm wondering if this is still the case for a given nRF5340 chip...
Hi,
If you use the following settings, an error will occur during commissioning.
Board: Custom board
SDK:ncsv2.9.2 OS: Windows10 Sample code:Matter Lock bord target...
Hello, I use nRF51822 based device with s110 softdevice. I noticed that data exchange is different on different connected centrals.
For test I used Windows and Android powered...
Hello,
I have my project up and running using the "nrf51-micro-esb" project. I can successfully set my device to PRX mode and have it receive payloads just fine. Similarly...
Hi,
I have an issue about power consumption with a board nrf52 10040. The consumption should be 100µA but is 500µA. I found an errata about that in ' infocenter.nordicsemi...
We're using nRF52 to read two sensors data: one is an ADC chip using SPI; the other is a PPG sensor using I2C. MCU sampling rate is 250Hz, meaning every 4ms, MCU will poll...
Hi all!
I'm a beginner developer.
I start my work with nrf51822, download examples e.t.c
Now I try to download my code in real PCB with external 16MHz crystal.
Code worked...
-----------------------------EDIT--------------------------------------
I've changed topic name, because not buffer overwrite is the problem.
I need some mechanism for...
I am working on a project for college in which I need to build my own PCB. The code works fine on the Dev Kit but on the PCB, the bluetooth is not showing. I have tried looking...
Hello,
I am using nRF UART v2.0 android app and I have added my custom logic above it. I am using this phone as the central device and nrf52 with sdk 12 as the peripheral...
hi
i am using two dongles.one would be sending sensor data from gpio to other through ble.i need a example code for those two.could you please tell me which example i can...
Due to limited budget, I have to use STLINK/V2 to flash code into nRF51822. I have been through steps of how to setup OpenOCD/STLINK/V2/nRF51822 in Ubuntu. After mass erase...
Hi. I'm using nRF52832, SDK13, S132v4.0.2.
I'm making peripheral device using nRF52832.
And I can see it gets BLE_GATTS_EVT_WRITE event as below when central sends WRITE...
I'm having a difficult time getting my project to link to the nrf_serial module
._build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_serial_read (referred...
Hi
From my understanding of the softdevice API, the maximum packet length is set using sd_ble_opt_set(BLE_GAP_OPT_EXT_LEN, &opt) , but the actual change to the packet length...
Hello,
I would like to build a sensor array that communicate with one master in a star topology.
I have played with the Gazelle protocol example ( gzll_ack_payload examples...
Hi,
I am working on a project where I have 4 advertising beacons which will have to trigger some functions in the central side when it gets the advertising data.
Now I...
