We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi DevZone
Does the SWF switch at the PCA10040 automatically switch to the antenna I have put on my connection probe? ( www.digikey.com/.../1775923)
Thanks in advance...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
Hi,
In the nrf52.h, SPIM_RXD_Type is defined as below.
typedef struct {
__IO uint32_t PTR;/*!< Data pointer */
__IO uint32_t MAXCNT;/*!< Maximum number of bytes...
i am working with Nrf52 + Visualgdb complier.
nrf_drv_gpiote.h contains designated initializers which aren't supported by C++. I'm including all SDK headers inside an extern...
Hi,
I would like read a long characteristic.
I know that I have to use sd_ble_gattc_read and I have to multiple call this function.
But I don't know where I have to call...
Hello,
I want to implement some kind of control point. This means, that I want to handle BLE write events to some characteristic. I've seen that the payload of the ATT...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
I'm interested in adopting nRF52840 as a mesh networking + Beacon device. It is my understanding that the Nordic SDK for mesh will only be released after Bluetooth SIG releases...
hello everyone:
I work IPv6 over BLE example on both Raspberry pi ,this pic is 6LN (CoAP Server)sending IPv6 over BLE packets to 6LBR(CoAP client) and I use tcpdump to...
Hi,
I'm testing the multi-link functionality.
I want to manage the connections with connection handler.
But, p_gap_evt->conn_handle passed thru on_ble_evt(); and p_ble_nus_evt...
