Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I use the nrf52832. In the beginning,I can download the code and it works well. And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
Hi, i'am working on a custom board on which there is two led drive by a led driver.
The two leds are wiring to be drive by pins P0.14 and P0.15, but unfortunately these...
Hello! I am using a nRF52832 device, along with SDK 12.1.0 and S132 v3.0.0. Data is being sent data through BLE and received on an Android phone.
After some tests I noticed...
I need to have a Central device physically connected (via UART) to a sensor. Data is collected from the sensor and sent to a number of Peripheral devices which use the data...
Take a look at these screenshots. With the trigger enabled, the average current consumption is reported at 13.21uA. With the trigger disabled , the average current consumption...
Dear Nordic,
I want to know if it is possible to send asynchronous data type from a slave node to a master node (master node would be in continuous scanning mode). Reading...
Here is my problem. I want to disable uart when there is no data coming into MCU.
I used IO LotoHi event to enable uart Rx. After finish data receiving, I disable Uart.
...
I've modded the PCA10040 DK for current measurement with an ampere-meter (TTi 1604), using a program which turns an LED on and off every 5 seconds. The measured current stays...
I am using an LG G5 and my co worker let me use a google pixel. I tried using the s132 softdevice along with the BLE UART example code from 12.2.0, I get the device is not...
I'm aware of GATT's Profile, Service and Characteristic.
And also, for GATT_Server, GATT_Client it can be Central or Peripheral. (As I manually set it.)
And also, the...
hi
I am using nRF51822(from waveshare). previously i was able to program my device with nRFgo Studio. But I am facing a problem now. I programmed my device with radio transmitter...
I want to collect data for analysis sent from peripheral(ble_app_uart example), I connected peripheral device to app(nrf connect) and enabled service, now the data is sent...
We want to build a network of many nodes (nrf52 boards) distributed in the apartments, that are connected via BLE over 6lowpan, of course using a border router for communication...
image description (/attachment/6196b4481c3f6fefbd0784b78d9163c9)
Hello.
I development education robot by ENTRY base.
PC(ENTRY base) + NRF51822 central
and
NRF51822...
