I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
We are using the nRF51822 on our product.
I'd like to know about the minimum value of RSSI ?
We checked the minimum RSSI value by using our products.
And most of...
Hello,
We plan to use the Serialization mode with the NRF52832 module.
We would like to know how is handled the low power mode when the NRF52832 module is used in Serialization...
I am adding a bootloader with BLE OTA upgrades. I am using SDK 11.0.0 and I based my bootloader in examples\dfu\bootloader . I can only fit a single bank upgrade (I upgrade...
Use the guide to compiler the UECC almost neet use 20 hours to finish it.
I think that Nordic need provide the after compilered uecc lib.
That will save so many time...
I have an accelerometer that utilizes IC2 (NXP MMA8452Q) that I am trying to integrate with the nRF51 DK. The accelerometer is on a breakout board, and is wired up very simply...
I have successfully been using the MIO ALPHA heart rate monitor with S120 0.8.0-3.aplha and SDK 5.1.0, using the SDK application "ble_app_hrs_c"
Im trying to migrate to...
I develop with MDK.
Now, I want to create a bootloader with 12.1?
Follow the instruction of the document, I must install micro-ecc, and ....
But as last...
For example:
region 0: 0x00000 -> 0x1b000
region 1: 0x1b000 -> 0x40000
In region 0: the first page(1024 bytes) is 0x400=1024 from 0x0000 -> 0x400 , ERASEPCR0 must be...
When I change the target from nrf51422 in the SDK into nrf51822 there is this error in Keil uVision Project window.
I can't find a way to remove the files in red warning...
Hello,
I have a problem with secure bootloader.
what I did:
Flash SoftDevice 130 using nRFgo Studio.
Compiling \examples\dfu\bootloader_secure\ (i removed the...
Hi guys,
I'm following the tutorials in devzone.nordicsemi.com/.../
I'm in the final step to show the GPIO in peripheral views, but there is no modules in the view....
Hi,
I´ve been reading a lot of question about the duration of the SOFTDEVICE_HANDLER_INIT, and I've found that if a change the accuracy of the calibration it will be faster...
Hi,
4.4.2 is known to have lots of BLE problems.
Is there a summary of the main known problems regarding BLE that have been fixed
in 5.01
in 5.1
.....
In general...
On dev kit nRF52 PCA10040, rev 0.9.0, Keil uVision 5.21.1.0, SDK nRF5_SDK_12.1.0_0d23e2a - I need to monitor 9 input signals for a transition (hi to lo) on any of the pins...
I'm trying to program a nRF51822 custom board using Debug out pin P19 of NRF51-DK through Keil MDK, here is the problem I encounter:
To simplify I just use the simple blinky_s130_pca10028...
