Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Using the Data Length Extension (DLE) feature in BLE v4.2, two nRF52 dev boards can achieve a maximum throughput of almost 800 kbps. I tested DLE with an iPhone 6 and the...
I am new to nRF ICs.
How to get 32.678KHz clock out from a pin? Is it possible? If yes, from which pin and how to configure it?
I am using 32.768KHZ external crystal fro...
I have designed several boards for the nRF51822-QFAA, namely with/for the Waveshare Core51822 module.
While one is working as expected - namely my "Orchid Lamp" (see links...
When softdevice S110 is used then bonding is not occuring (via nrf connect app to nrf51).but both devices get bonded when s130 is used?In Nrf connect app key matching failed...
Hi,
I have a working project where I use PWM driver with LEDs on the development board. I make use of the d52_starterkit.h where I have the following definitions:
#define...
Hi,
On a system reset, we want a mechanism to stay in bootloader for a short period before jumping in application. This way, if something is wrong in application that prevent...
Hi,
I am using ESB library for nRF52 microcontroller. At receiver i want to measure RSSI value of a packet. I got RRSI from nrf_esb_payload_t structure.
I am printing...
Hi,I have ibeacon (nRF51822) radioland-china.en.alibaba.com/.../long_range_300m_ibeacon_programable_nrf52822_beacons_bluetooth_4_0_tag_chip.html . I want to update the firmware...
Hi,
In my project i would like to save 100 bytes of information in RAM before going to System-off sleep mode.I have tested the example project given in sdk11 works okay.Have...
I am trying to read the battery level on a custom NRF52 board and I am getting a value that is around half of real voltage.
The same code works fine on NRF52 DK ( I was expecting...
I am looking at this example: github.com/.../main.c
In ble_evt_dispatch (line 315), this function forwards an BLE event to all of the modules. By looking at ble_evt_t,...
I am trying to build a BLE central application on the mbed compiler (target BLE Nano).
I have chosen the ble_app_uart_c example from the nRF5 SDK as a starting point. My...
Hi Support Team,
one error come out when use nrf connect, just as attached picture shows,
please help to check what cause this error,
no error come out on phone.
...
