I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
I want to combine two applications, both of them having two services. One application resides at 0x16000 and other one resides at 0x249f0. I am using softdevice 7.3 and sdk...
I am using nrf51822 and softdevice 7.3. I am working on the github mesh example. I want to add uart service with mesh, so that I can communicate with that particular device...
Hello, this is what I can think of when porting a project, but before that, a little background about my project:
it uses BLE (duh)
it uses uart to print test output...
Hello,
i am using the nRF52 Development Board with SDK 11 and I have trubble with the UARTE Interface with DMA. Parallel I have running the ESB protocol.
I know the problems...
hello there i want to add battery service and thermometer service in advertisement packet. so i changed in uart project. but in advertisement project i can see battery service...
hi
I used the nrf51 dongle to receive advertisement packet from other nrf51 dongle. I used this formule, d = 10 ^ ((TxPower - RSSI) / 20) , given from this link forums...
Using Command Line Tools 9.0.0 attempting to push code.
ERROR: JLinkARM DLL reported an error. Try again. If error condition
ERROR: persists, run the same command again...
Hi All,
I am attempting to use 6 PWM channels with the app_pwm library on the nRF52 and am only able to successfully get 4 pwm outputs. Upon changing the 6th channel (PWM2...
I need 3 time aligned PWM channels (period of all three channels needs to start at the same time) at about 100 Hz with 16 bit resolution on the duty cycle. I also need to...
hello,
I used nrf52 and softdevice 2.0.1 and i have a big problem.
For some times the BT works perfectly but after i connect more then 4 devices for some reason
the...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
Hi Nordic,
It's hard to find an example to talk about the event of advertising. I checked the advertising chart and know I will get the event BLE_GAP_EVT_TIMEOUT. Where can...
Hi,
I attended a training session run by the BT SIG last week and met a helpful Nordic chap who, when I mused about how I was using a programming board to run a sensor...
Hi i am having doubt in RTC configuration.I am using RTC1 and i want to produce ticks for every 1 minute.I have combined the UART and RTC example to get the RTC output in...
Hello
i am using the Nrf52 with pca 10036 board. i am working on fruitymesh to work on visualgdb.
i am getting problem here
"#pragma pack(push)
"#pragma pack(4)
...
