Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi,
I'm using s132, sdk 12.1 on nrf52x, my question is about possible race condition when setting the value of a characteristic using sd_ble_gatts_value_set (on peripheral...
Hi,
I am working on a IoT based project with nRF52832 and nRF52840. I am looking for PCB Designers and people who can develop firmware for our project. The firmware development...
Hello, in S110 device's nrf_sdm.h, there is this enum "NRF_CLOCK_LFCLKSRCS" which is defined as:
enum NRF_CLOCK_LFCLKSRCS
{
NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, /**< LFCLK...
Hi..!
I am trying to ***Receive ACCELEROMETER DATA FROM MPU6050 to PCA10028(NRF51822) AND WANTING TO PRINT IT ONTO UART using KEIL IDE.
Code is getting compiled & getting...
HI.
I want to send data from nRF24L01 + to RF communication and receive it from nRF24LU1 +.
The nRF24L01 + is connected to the STM32. The settings are as follows.
...
Hi, I'm trying to build a bluetooth device that pairs once, and does not have other hosts maliciously or accidentally pair to it (which would create a poor experience for...
Hi,
When i used nrf51822, i remember the s110 define max transmit buffer as 23 Bytes, but now, i am using nrf52832, the max transimit buffer is defined as 158 bytes.
Does...
Hello, I understand this may be a very broad question, but I still need to find as much information as I can.
Give a general answer if you'd like to, or a very specific...
Hi,
I just got the email about SDK13.0 official release. The list of changes in this release include "Secure DFU improvements". What does it mean?
Is Buttonless Secure...
Hi Engineer!
I would like to use DTM mode to test nrf52840 in our pre-samples.
but i did not find any info about that. how to use DTM in this chip ?
thanks you!
I've recently migrated from SDK11 to SDK12.3 using a FreeRTOS based applications. I seem to get a hardfault on a sd_ble_gatts_hvx call. There is no difference between my SDK11...
I have studied uart source code.
github.com/.../Android-nRF-Toolbox
And I get confused about the action of reconnection.
AutoConnect flag says It will look up "white...
IOS APP, when in the OTA upgrade, into the background, OTA stopped, at this time into the front desk, can not continue to upgrade, how can you continue to upgrade after entering...
