i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
In ble_app_uart, the tx and rx characteristic uuid are shown below, and it supposed that the Tx characteristic enable notifications while the Rx characteristic enable write...
The hardware I am using is based on nrf51822/pca10028, with s110 SoftDevice version, and the SDK version for the project is 8.1.1 Using Keil uVision 5.21.A
When opening...
Hi,
I am running the mqtt subscriber example provided in IoT SDK (nrf5_iot_sdk_3288530).
I am using raspberry pi as router, and following the infocenter tutorial .
I have...
Hi ,
This is the first time I am using nRF52 and I don't have any experience about Antenna design. Here is my question: I am using nRF52 CIAA variant and planing to use PCB...
Hi,
I need to change advertisement data while advertising. The goal is to set new data for every packet. Firstly, I was trying to put new value like this, but it didn't...
hi all:
Recently, I develop with nrf52832, the softdevice is nRF52_SDK_0.9.0_0c82e3e.
In my application, I need a big buffer, so 32K ram can not satisfied. As the errata...
Hi all, we designed a custom board using nRF51822 now we need to test these custom boards working properly are not for these I'm creating a factory test project by configuring...
Hello Nordic Semi Developers..
I design my Product prototype using NRF52832
What is the plan of Nordic to provide SDK to support NRF52832 dynamic Mesh with
[1] Over The...
Hello,
I want to read the current ticks in RTC0, and want to measure the time elapsed after some events by using ticks to milliseconds.
Basically i want to display the...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
What I want to achive:
Get the IoT-SDK 0.8.0 MQTT-Example running on nRF51 and publishing sensor data...
I am using nRF51 IoT SDK and nRF51-DK.
After setting up Raspberry Pi3, I ran icmp sample in the SDK for testing ping6.
when sending about 60k byte, we could not send the...
Hello, I used to think that handles are just a member of a stuct or perhaps a field of a packet, which is used to identify data payloads.
Now it seems that I might have...
Hi,
I have a problem with the nrF8001. I connected to STM32F4 and I use the nRF8001 SDK v1.7.
I need send several (less then 20) bytes from the device to the phone with...
Hello,
I used nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0, the ble_app_uart_c example code.
I want to add the timer, after add the following code, my system can't work....
