I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
I would like to use assembly language instructions for the following piece of code:
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<NUMBER_OF_SHORT_PULSES_TO_TURN_BSTR_ON;i...
Hi,
I wrote a function setting some GPIO pins, initiating an SPIM transfer (with EasyDMA), then waiting for the SPIM handler to signal end of transfer, and then set some...
HI,
I am using nrf51822 to communicate with ADT7320,using nRF51822 as the master,and the ADT7320 as the slave.I used the SPI master example,then i want to get temperature...
I've not been able to program the nRF51822 using the Blackmagic probe programmer because the nRF51822QFAAH1 seems to use a previously unseen device code of 0x008F
Could...
Hi guys!
Got a problem with re-initialising my SAADC to read my current battery voltage. I'm using SDK11 and don't want to migrate to v12, so I wanted to do a workaround...
Hi,
Im using SDK11 and id like to use serial DFU, when i try to run pc-nrfutil I get a message "Serial transport is currently not supported".
Id like to write own update...
Hi,
I just upgraded to the new SDK (12.1) from SDK 11... and I'm completely lost about the new secure DFU... Previously I correctly implemented a buttonless DFU in my application...
Hi,
I make some tests on power consumption of nRF52 with evaluation board and I remark some peak on the current. it's appeared that this peak is generate by DEC4 output ...
Hi, if i pair my nrf51-dk with my iPhone works, than I pres discontent (bluetooth settings),
now,
if I try whit another iPhone this doesn't work...
If I reset the board...
Hi,
I think there's an error in SDK12's nrf_drv_uart, some code parts unconditionally use p_instance->reg.p_uart (eg. nrf_drv_uart_task_address_get, interrupts_enable)...
Hi
Recently in the release notes of the SDK12 I noticed a line about updated the MDK update:
Included a critical MDK update (v8.7.1)
My SES project uses the...
Hi,
Is there an example available for Nrf51822 BLE HID (nrf5 SDK v11) with Feature and Output reports?
I've added an output HID report to HID mouse example from SDK and...
Hello.
I use nRF52 and tried to make the shared channel.
There are 1 Master and 1 ~ 3 Slave device.
When the master device send the notification messages to slave...
Hi,
I just did a quick diff using these two commands
> find nRF5_SDK_12.0.0_12f24da/ -type f | grep --text -v -e "c$" -e "h$" -e "s$" | sed 's/.*\///' | sort -u > exclude_list...
Hi
we are switching from NRF51 to NRF52.
Putting the same (very basic) inits for sd and advertising, leads to NRF_ERROR_INVALID_PARAM..
This is my source:
#define...
