VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi,
I have install openocd on ubuntu. but i after running next line
openocd -f interface/stlink-v2.cfg cfg -f target/nrf51_stlink.tcl
i got these error.
Runtime...
Hi,
I'm trying to modify one of the examples (the hrs_relay) to find my custom service to identify the device uniquely. I know I need to add the 128bit uuid using and then...
I'm trying to transmit a radio signal inside time slot handler, the code is like:
switch (signal_type)
case NRF_RADIO_CALLBACK_SIGNAL_TYPE_START:
radio_configure...
I'm working with nrf52832 dev board. I used nRF Connect app for IOS but my phone run on IOS8.4.1, so i can't get it from apple appstore. Someone can help me by give version...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi there,
I'm using nrf51822 timer1 as the timer for some time-critical task, and I'd like to ask two questions about it:
What's the precision of Timer1 if the...
Hi
I am using nRF51822 (pca10001).I am unable to discover my device. I used the ble_app_template_s130_pca10028 as my base and added the code for gpiote handler as following...
Good day,
I tried the BLE Mesh Example located:
devzone.nordicsemi.com/.../
... and for some reason it is not working for me. I posted a comment where the example is...
Hi.
Faced with a strange situation.
Example. All look good when I read code area:
void ex1 (void)
{
uint32_t *addr_out;
uint32_t i,word;
addr_out=(uint32_t...
We've developed a custom board based on the nRF51822-QFAA and an MPU-6050 IMU. It runs on a li-pol battery and uses S110.
I've encountered a strange problem when power...
Hi,
I am working on measuring the voltage on a lithium battery (norminal 3.7V) with a voltage divider on nRF52832. The voltage divider combines a 510K and 360K resistor...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
We have a custom board using the ISP130301 BLE module (containing a nRF51822, 16MHz xtal, 32kHz xtal). Our apps work fine (gcc, SDK6, S110v7) except for high system on idle...
i don't see where the command queue index, m_op_queue.rp, is initialized.
when queue_process is called, the following line blows up:
fds_op_t * const p_op = &m_op_queue...
