Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
In arm_startup_nrf52.s (in the 8.9.0 device family pack), there is a new bit of code:
IF :DEF: __STARTUP_CONFIG
#include "startup_config.h"
ENDIF
I assume this...
Hi,
I'm thinking of using the NRF52 for an embedded wearable sensor application.
How much flash and Ram space can I expect to have remaining approx. for my application...
I'm a bit at a loss of how to voluntarily stop advertising: My related thread says I should call sd_ble_gap_adv_stop() , but when I do, no corresponding event is raised by...
To install micro-ecc, complete the following steps:
Install version 4.9-2015-q3-update of the GCC compiler toolchain for ARM. You can use ARM's Launchpad to find the toolchain...
Hello everyone,
I am currently porting a project from pstorage to FDS.
I am testing the functionalities of FDS including create, update and delete records and I am at...
Hello,
To reproduce this problem I use these steps:
Bond to NRF51822 using Android 6.0.1 and latest nRF Connect version;
After successful bond, connect to NRF51822;...
Hi,
We are using PPK board (PCA63511), we have followed the "PPK user guide" and installed all the necessary softwares, We have made the connections and switches option...
Hello everyone, I'm Dario.
I'm trying to work with a ble nano with nordic component. My target is to receive a string via serial periferial and sending it via bluetooth as...
I am a new engineer working with nRF52 and SDK 12 using Makefile project and arm-gcc. I wrote some simple code to try TWI Master and control a i2c slave device. My question...
Hello I just bought
SKYLAB bluetooth accelerometer sensor SKB360 bluetooth low energy nrf51822 bluetooth 4.0 low energy module
skylab.en.alibaba.com/.../SKYLAB_bluetooth_accelerometer_sensor_SKB360_bluetooth_low_energy_nrf51822_module_bluetooth_4_0_low_energy_module...
Hi,
Im trying to wake up from SYSTEM OFF using LPCOMP.
Im using the following code to power off:
nrf_drv_lpcomp_config_t config = NRF_DRV_LPCONF_DEFAULT_CONFIG;
...
Hi,
I am working on a Beacon application based on nRF52 DK and Eddystone protocol. So i am searching if there is already some examples/SDKs from nRF which supports both...
Looking for document or u tube to program nrf52832 using tag connect (6pin noleg) and nrf52 DK. Have the hex program and put it on the nrf582 dk. need to take to the next...
