I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am trying to use timer with Bluetooth application . I want to provide precise time stamping using timer for each bluetooth event. But program execution stucks...
Hi,
I'm using nRF5 SDK V11、s130_nrf51_2.0.0_softdevice. My application has added the DFU service . I download application,softdevice and bootloader to nRF51822 AC, the...
i m using pca10028 with gcc tool chain setup in windows...now i m using sdk 8 and work inside ble_uart code...i was add rtc1 inside that code sucsessfully but now.. when device...
Hello,
I am currently testing the nRF51 series as a possible upgrade to our products that use the 24L01P. For testing I have the nRF51 dev board setup as the PRX and a...
I'm using SDK 11 on my nrf51 chip. I'm trying to output a 120hz pwm but it doesn't seem to be producing at 120hz. I have a 120hz signal i'm trying to match and it blows pass...
Dear Wang,
I am unable find any documentation and board Initialisation code on how to change PIO from analog to digital output. but can't seem to locate the setting.
...
Hi,
I am working with MLX90615 sensor and is working with nrf_drv_twi functions and I could collect data as well. Now I need to put the sensor to sleep mode. Entering to...
Hi,
I'm trying to connect DWM1000 with SPI using spi_master.h.
When I have written to registry e.g. 0x11, 0x12 and read it I've got bytes: 0xFF, 0x11.
If I read three bytes...
Hi
I'm wondering if anyone have had any success or problems with generating and using secure DFU keys under Linux?
I'm using the latest nrfutil from: github.com/......
i am using nrf52832 pca10040. i tried to run the ble blinky example from package installer. it compiles without any error, but when is load it to the DK it will not even advertise...
NRF52832 is bluetooth pre approved SoC. So still need to pay Buetooth SIG to sell my Bluetooth based product in INDIA ???
Can i Sell non Certified product Without FCC CE...
Hi Nordic Forum!
Looking for the right configuration for the connection parameters, found different references to this Apple guide .
The problem is that in the 3rd condition...
I'm working on a project where I need to recognize whether or not a wireless tag is within 5-10' of a stationary reader. I would develop the reader system using a module,...
