Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I have just read nRF52840 Engineering A Errata v1.0, it looks like nRF52840 is like swiss cheese.
When can we expect some solid version of nRF52840 chip on the market?
Hi DevZone
Does the SWF switch at the PCA10040 automatically switch to the antenna I have put on my connection probe? ( www.digikey.com/.../1775923)
Thanks in advance...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
Hi,
In the nrf52.h, SPIM_RXD_Type is defined as below.
typedef struct {
__IO uint32_t PTR;/*!< Data pointer */
__IO uint32_t MAXCNT;/*!< Maximum number of bytes...
i am working with Nrf52 + Visualgdb complier.
nrf_drv_gpiote.h contains designated initializers which aren't supported by C++. I'm including all SDK headers inside an extern...
Hi,
I would like read a long characteristic.
I know that I have to use sd_ble_gattc_read and I have to multiple call this function.
But I don't know where I have to call...
Hello,
I want to implement some kind of control point. This means, that I want to handle BLE write events to some characteristic. I've seen that the payload of the ATT...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
I'm interested in adopting nRF52840 as a mesh networking + Beacon device. It is my understanding that the Nordic SDK for mesh will only be released after Bluetooth SIG releases...
hello everyone:
I work IPv6 over BLE example on both Raspberry pi ,this pic is 6LN (CoAP Server)sending IPv6 over BLE packets to 6LBR(CoAP client) and I use tcpdump to...
