I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
I have been trying nrf-sniffer with no success. Setup is:
Win7 64,
Sniffer Win 1.0.1,
Wireshark 1.10.14 (both win32 and 64 tried),
PCA10000 and PCA10001
The sniffer...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
So, I want to make an application where my NRF52 advertises an URL via the Eddystone beacon.
The URL will link to an webpage, that will connect to my device through the physical...
As here said link1 If we want to use flash in the mesh we should ignore APP_ERROR_CHECK(NRF_ERROR_INVALID_STATE) in ts_sd_event_handler() ,
2.And here link2 tell us...
How do I set up a variable length characteristic which is greater than 20 bytes and use notifications with this characteristic?
For example I have several variable length...
In an nRF51-based application I'm working on, I am using the SPIS peripheral and a generated clock signal to send a large buffer out over serial using DMA. I want to use the...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
hi
in tutoriall service beginer there is
static void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;
// Build advertising data struct to pass...
wireshark 2.0.3 which is what got installed when I downloaded it is not supported according to the nFsniffer program.
So what, and how do you set this up?
I am using a function to read the die temperature data from nRF51822 as follows:
static uint32_t temperature_data_get(void)
{
int32_t temp;
uint32_t err_code;
...
Hi all,
my Setup :
nrf51822 QFAC Build Code A1,Waveshare Core51822 Board
keil microvision
nrf device family Pack 8.6
without Softdevice erased with openocd...
Was testing DFU Failures scenarios on SDK 10 to make sure that the software elegantly handles when an Image fails to transfer/swap/load/disconnect..etc. I find that when an...
Using adafruit sniffer. Windows 7 32 bit professional, windows 7 64 bit professional.
After installing the FTD drivers I see com5 installed.
when I start the sniffer it...
