Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi Nodic enginner;
Now i am using 51822 in my product. I find that there is a 2.5mA current in my board that is no firmware. The question i want to ask is that how much...
I have made a basic pcb for a school project, with just the nRF51422 chip, a J-LINK programmer and and antenna on it. I am trying to test the functionality of it. I have gotten...
Is there any reason I could not modify this demo to use IRK values and allow whitelist scanning based on stored IRK values? I'm wondering why the demo seems to have an option...
Hi everyone,
I am using the nRF51 SDK 10.0 with the Rigado BMD-200 Evaluation Kit and want to print debug messages to UART or something similar.
I am trying from main...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
I followed the instructions from here developer.nordicsemi.com/.../a00081.html
to make my application support DFU OTA. Despite of some errors in the instructions I managed...
Now I am using hid mouse example to develop a project which requiring bond process. Everything is OK but the question: I need report the btn number which trigger the system...
I copied the example "ble_app_hrs_s110_pac10028(nRF51 PCA10028)"in the nRF51 sdk 10.0.0. I Changed the configuration to make it run on BOARD_PCA10001. But the program keep...
Hi,
I need to update the Min and Max connection parameters run time.
Is it possible to do so?
Also can i update the Min and Max connection parameters through an iOS app...
Hi,
I am using app_pwm in low power application on nRF51822 with soft device S110. Today I measured power consumption and found the current was ~1.5mA during advertising...
Hello,
There are two problems on nRF52 ble uart example code.
I would like to know is there any misunderstanding or mistake I made?
or anyone met the problem too.
1...
Hi All,
I am starting the process of getting our product Bluetooth RF PHY tested, and our lab has asked an interesting question.
What is the image frequency of the nRF51822...
Note: I am using v8.0.0 of the s110 softdevice on the nrf51822.
I am developing an application with the nrf51822 that uses pstorage, bluetooth, and SPI reads/writes.
...
