Setup
Fanstel BC15M-V3 module (nRF54L15, FICR 0x340 = 0x1C , 0x344 = 0x01 , i.e. Revision 1) on a small custom board. The only other active part is a TDK ICM-45686 IMU...
Hi Nordic DevZone Team, I have a question related to Errata 78
Chip / environment
nRF52832
SoftDevice - S112, SDK 17.1.0]
Does this errata apply to the softdevice...
Hello,
I tried following the exercise until the part where you start a debugging session. I looked at the thread viewer and the result was different than what was on the...
We are moving to the Thingy91x after shipping over 1000 thingy91s. We are struggling though with evolving our production tools. Currently for the T91 we have a very slick...
Hello Nordic team, We are experiencing an issue on a product using the nRF52840 where the device occasionally enters a state from which it cannot recover without a complete...
Dear Nordic team,
we are developing an LTE-M/NB-IoT device based on the nRF9151 with a compact chip antenna (Würth 7488918022). Our target bands are B12, B2, B4/B66 (AT&T...
Hi. I'm working on a BLE system with Central and Peripheral with nRF5340 with 70msec of CONN_INTERVAL and about 1sec of SUP_TIMEOUT. The Central unit also has a UART that...
HI
In the RF_Test example, there are 80 channels.
However, BLE has only 40 actual channels.
Why are there 40 channels...? I would like to know.
Do 80 channels...
Hi,
I am new to the NRF and private-public key pair using.
Can anyone please explain me how to use custom keys for MCUBoot, I added below config in /child_image/mcuboot...
Hi all
We are using ztest in our project because it works nicely together with twister, Zephyr's test runner tool. We need to have the ability to mock modules. For this...
Hi Team
we have NR52833 ,NRF52 these boards Serial no : 10001208 , 10001220
we use these devices in wipro BQTF as reference devices and not for any production. We are...
Hi
I read this Q&A: How to configure the P0.00 and P0.01 pins as GPIO , which is similar to my question. There are some things I did not get from that section:
"Physically...
Hi there, I am trying to do a blocking simple ADC measurement in using NRFX drivers in a threaded context, however when I build I get the following error:
gen_isr_tables...
Hi,
I am using nRF9160DK v0.9.0 with Cellular Monitor 2.4.0, and I have flashed AssetTracker2 via the "Program device" button.
Although asset tracker works fine uploafing...
Hi,
Using the nrf Connect Programmamer v4.2.0, I get the following error when connecting to J-Link on some of my custom boards (about 30%):
When I run nrfjprog...
I am attempting to enter a sleep state (System Off) with a wakeup button . I set all of my GPIO pins to the default config except for my wake up, configure the appropriate...
Hi
I am unable to get the Guiconfg to work in lesson 1 exercise 2 of the nRF Connect SDK Intermediate course.
I have attached snap shots of the output when I try to run...
I'm using the custom board of nrf 5340 with 7002.
When I run the sample project of Hello World, the current is about 90 ma,
and I run the sample project of WI-FI Scan...
We are going into sleep mode for the processor. We are using Zephyr and sdk 2.3. We also are keeping a running count of seconds and synching that once a day with a modem....
Hello,
I'm working on a product using the nRF9160 and facing challenges with poor LTE signal strength, leading to significant power drain when the device goes offline. I...
